Search found 458 matches

by sellis
Wed Apr 09, 2003 1:41 pm
Forum: Cat Talk
Topic: Difference between model years
Replies: 2
Views: 1438

Re: Difference between model years

fyrfyghtr All of our models have been wood free since the very first boat built.The transom kit that you are talking about is a aluminum brace that fits over the cap of the transom. We require it to be installed on all boats between 2000 and 2002 model yaers.2003 and 2004 model years we have raised ...
by sellis
Wed Apr 09, 2003 1:16 pm
Forum: Cat Talk
Topic: bobbing or fishtailing
Replies: 3
Views: 872

Re: bobbing or fishtailing

jla counter rotating engines will help this situation. For the time being get the boat runing level then trim both engines until you actually start cavitating,then trim both engines down until cavitation stops. This is where you should be running the boat.The world cats run the best when you can tri...
by sellis
Tue Mar 25, 2003 1:38 pm
Forum: Cat Talk
Topic: Question for Scott
Replies: 2
Views: 788

Re: Question for Scott

Artur Unfortunately I have not ran a boat with the hydrofoils that had two standard rotating engines. My guessing would be that it would correct the problem some but not completely. I am sorry I can't give you a positive answer but it is really trial and error when it comes to stuff like this. Hopef...
by sellis
Fri Mar 21, 2003 3:24 pm
Forum: Cat Talk
Topic: Counter Rotation on a Cat or not??
Replies: 2
Views: 910

Re: Counter Rotation on a Cat or not??

jjbertucci I have ran world cats with and with out counters. From my experience with the non rotating engines is that the boat wants to veer one way. This can be corrected by trimming your engines. I also have noticed that spinning the boat at the dock is not as good if you have non counters. As far...
by sellis
Fri Mar 14, 2003 11:30 am
Forum: Cat Talk
Topic: Where can I mount speakers?
Replies: 8
Views: 1962

Re: Where can I mount speakers?

266sc you can mount your speakers in the back where you are talking about. There is rigging tubes that run on top of your toe kicks that you should avoid. I would suggest that you look inside your battery compartment,from there you can look around the corner and see your tubes. Determine how high th...
by sellis
Tue Mar 11, 2003 3:11 pm
Forum: Cat Talk
Topic: Mounting Transducer
Replies: 10
Views: 2371

Re: Mounting Transducer

The transducer that I am referring to is called a low profile or a flush mount thru hull transducer.They only extend down about a 1/4 inch. They resemble the scupper fitting on the side of your boat. You can contact Airmar, they are the company that makes transducers for almost every brand electroni...
by sellis
Tue Mar 11, 2003 1:51 pm
Forum: Cat Talk
Topic: Mounting Transducer
Replies: 10
Views: 2371

Re: Mounting Transducer

When mounting your transducer I always try to put it so the bottom edge of your transducer is about a 1/4 below the flat area on one of the outside chines. The transducer should come with mounting hardware for ataching your cable and for running the cable through your transom or motorwell. I recomen...
by sellis
Mon Mar 10, 2003 5:46 pm
Forum: Cat Talk
Topic: High readings on Flow meters
Replies: 16
Views: 3527

Re: High readings on Flow meters

After discussing your situation over the phone I have come to the conclusion that your pickup tube has a pin hole in it at the weld that holds the pickup in place inside your tank. Florida Marine tanks is sending me a kit that basically is a new pickup fitting that has a nylon tube attached that wil...

Go to advanced search